Guide to your keypad and operating your system
Function | Purpose |
---|---|
Away | Arms the entire system, both interior and exterior zones. Entry/exit delay is activated. |
Stay | Arms only the exterior zones of the system. Allows interior movement within the premises, without causing an alarm. Entry/exit delay is activated. |
Bypass | Removes individual zones from monitoring, at the time the system is armed. |
Chime | When set, the opening of exterior zones while the system is disarmed, will sound 3 beeps from the keypad. |
Fire | Activates an audible pulsing sound of the siren and sends a signal to the Bell MTS Monitoring Centre. |
Police | Sends a signal to the Bell MTS Monitoring Centre, without an audible sound. |
Instant | Same as stay mode, with no delay. |
- Vista 15P/20P keypad instructions
How to: Steps: Add/Change a User Code [Master Code] + [8] + [2-digit user #] + [new 4 digit code]+ [new 4digit code again]
If changing the Master Code (User #02) enter the new Master code twice, as opposed to once for any other code. Keypad will emit it a short beep if done correctly.Check for Faulted Zones [ * ] Delete User Code [Master Code] + [8] + [2-digit user number] + [#] + [ 0 ]
Keypad will emit a short beep if done correctlyArm Away Mode [4 digit code] + [2] Arm Stay Mode [4 digit code] + [3] Arm in Night-Stay mode [4 digit code] + [3] + [3] Arm in Instant Mode [4 digit code] + [7] Arm in Maximum mode [4 digit code] + [4] Disarm [4 digit code] + [off] Bypass zones Same as stay mode, with no delay. Toggle chime on/off [4 digit code] + [9] Quick Arm Away [Away] press and hold Quick Arm Stay [Stay] press and hold - Lynx 5100/5200 Touch Screen keypad instructions
How to: Steps: Add/Change a User Code [ TOOLS ] + [4 DIGIT MASTER CODE] + [USERS] + [ADD NEW] + [NAME] + [ENTER NAME] + [DONE] + [4 DIGIT USER CODE] + [DONE] Delete User Code [TOOLS] + [4 DIGIT MASTER CODE] + [USERS] + [DELETE] + [YES] Arm Away Mode [ ARM AWAY ] + [ USER CODE ] Arm Stay Mode [ ARM STAY ] + [ USER CODE ] Arm in Instant Mode [ ARM STAY ] or [ ARM AWAY ] + [QUICK ARM ICON] Check System Status Select [SYSTEM] icon Disarm [ DISARM ] + [ USER CODE ] Bypass zones Select [ ZONES ] icon Toggle chime on/off [ Settings ] + [ Chime ] + [ On/Off ] - Lynx keypad instructions
How to: Steps: Add/Change a User Code [MASTER PIN] + [CODE (8)] + [User # (02-06)] + [NEW PIN] Delete User Code [Master PIN] + [CODE (8)] + [User # (02-06)] - (Wait until they keypad beeps once before pressing any other key)
Do NOT delete master code (02)!Arm Away Mode [PIN] + [AWAY] or just [AWAY] Arm Stay Mode [PIN] + [STAY] or just [STAY] Arm in Instant Mode Press [NO DELAY (0)] immediately after arming Check System Status [STATUS (*)] Disarm [PIN] + [OFF] Bypass zones [PIN] + [BYPASS (6)] + 2 digit zone number Toggle chime on/off [ Function (#) ] + [ Chime (9) ] - DSC PC1555 keypad instructions
How to: Steps: Add/Change a User Code Enter [*] + [5] + [Master Code]
Enter [user number 01-32] to indicate which code you wish to modify.
Enter [new 4-digit code]
Enter [#] to exit user programming mode.
*To change master code, the user # to modify is [40]Delete User Code Enter [*] [5] [Master Code]
Enter [user number 01-32] to indicate which code you wish to modify.
Enter [*]
Enter [#] to exit user programming mode.Arm Away Mode Enter [4 digit Code] when Ready Light is on Arm Stay Mode Enter [4 digit Code] and during exit delay do not open a door
(The system knows you haven't left and will automatically bypass any interior zones such as motion sensors)Arm in Instant Mode Enter [*] + [9] + [4 Digit Code] Disarm Enter [4 digit Code] when Ready Light is on Bypass zones Enter [*] + [1] + [2-digit Zone #] + [#] Toggle chime on/off Enter [*] + [4] If Alarm Sounds Enter [4 digit code] to silence - DSC PC1616 keypad instructions
How to: Steps: Add/Change a User Code Enter [*] + [5] + [Master Code]
Enter [user number 01-32] to indicate which code you wish to modify.
Enter [new 4-digit code]
Enter [#] to exit user programming mode.
*To change master code, the user # to modify is [40]Delete User Code Enter [*] [5] [Master Code]
Enter [user number 01-32] to indicate which code you wish to modify.
Enter [*]
Enter [#] to exit user programming mode.Arm Away Mode Enter [4 digit Code] when Ready Light is on OR Press and hold [Away] for 2 seconds Arm Stay Mode Enter [4 digit Code] and during exit delay do not open a door
(The system knows you haven't left and will automatically bypass any interior zones such as motion sensors)
OR Press and hold [Stay] for 2 secondsArm in Instant Mode Enter [*] + [9] + [4 Digit Code] Disarm Enter [4 digit Code] Bypass zones Enter [*] + [1] + [2-digit Zone #] + [#] Toggle chime on/off Enter [*] + [4] - ADT Safewatch Pro 3000 keypad instructions
How to: Steps: Add/Change a User Code [Master Code] + [8] + user no. + new user's code. Keypad will beep once to confirm new code Delete User Code Master/Part. Prog. code + [8] + [user no.] + [#] [0] Arm Away Mode Enter code + [AWAY] Arm Stay Mode Enter code + [STAY] Arm in Instant Mode [#] + [INSTANT] Disarm [4 Digit Code] + [OFF] Bypass zones Enter code. Press BYPASS key. Enter zone number(s) to be bypassed (use 2-digit entries) Toggle chime on/off [4 Digit Code] + [Chime]